Q: Can I purchase the .22 bolt with a charging handle pre-installed?

Asked by: Phillip? McMicken - 9/28/2024
A: Hi Phillip,
You can purchase them together but they are still two separate parts. -Good shooting!
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Administrator (9/28/2024)

Q: Does this bolt have last round hold open? Thanks!

Asked by: brinc - 7/16/2022
A: KIDD does not offer a last shot hold open.
Was this answer helpful?  1 of 1 Customer(s) found this Answer helpful.
Answer provided by: Shalee (7/16/2022)

Q: Will the Kidd bolt fit into a Brownells BRN-22 receiver?

Asked by: Mark Zerinskas - 6/29/2022
A: Yes, the KIDD Bolt will work.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (6/29/2022)

Q: Do Kidd bolts come with a lifetime warranty?

Asked by: Randal Klefbeck - 4/18/2022
A: Yes, all KIDD products come with a lifetime warranty.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (4/18/2022)

Q: Will a Kidd bolt work with a Brownells 10/22 receiver?

Asked by: Vic - 1/24/2022
A: Yes, the KIDD bolt should work in that receiver as long as their tolerances are correct.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (1/24/2022)

Q: Will Tony’s bolt fit in the Bergara BXR 22lr 10/22 receiver?

Asked by: R Shook - 1/13/2022
A: Yes, the KIDD bolt should work with that model.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (1/13/2022)

Q: Are your 10-22 bolts made of stainless steel?

Asked by: GEORGE LEWIS - 6/1/2021
A: Yes, all KIDD Bolts are made from stainless.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (6/1/2021)

Q: I have a Ruger 10/22 Charger and wanted to know if your KIDD bolt will work with the Charger AND a Franklin Binary Trigger? Your time and assistance is greatly appreciated. Darren

Asked by: Darren - 12/13/2020
A: Yes, it will work with that setup.
Was this answer helpful?  1 of 1 Customer(s) found this Answer helpful.
Answer provided by: Shalee (12/13/2020)

Q: Do you sell a completed bolt for the 10-22 with all of the upgrades?

Asked by: Michael Evancik - 12/8/2020
A: Our bolt comes fully assembled with the upgraded firing pin and extractor installed.
Was this answer helpful?  1 of 1 Customer(s) found this Answer helpful.
Answer provided by: Shalee (12/8/2020)

Q: What headspace depth do you use on the bolt face recess of your bolts?

Asked by: Pete - 10/8/2019
A: The head spacing on our bolt are .042
Was this answer helpful?  5 of 5 Customer(s) found this Answer helpful.
Answer provided by: Shalee (10/8/2019)

Q: Will it damage this bolt in any way to dry fire to practice? I know with the factory bolt it has a firing pin stop that wears out. So I am curious how your bolt holds up to dry fire?

Asked by: akuser47 - 12/25/2018
A: You can dry fire the bolt as much as you would like.
Was this answer helpful?  1 of 1 Customer(s) found this Answer helpful.
Answer provided by: Shalee (12/25/2018)

Q: Will this go into the Ruger stock receiver and work well?

Asked by: Tim - 9/29/2018
A: Yes, it will work great.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (9/29/2018)

Q: Will this Bolt drop into a stock 10/22 Take Down? Thanks.

Asked by: Mike - 12/23/2017
A: Yes, this bolt will work in that model.
Was this answer helpful?  0 of 0 Customer(s) found this Answer helpful.
Answer provided by: Shalee (12/23/2017)

Q: Howdy, I have one of your bolt charging assemblies. With the stock bolt, it is kind of sloppy and the handle rubs on the receiver. If I purchase one of your bolts will it all fit tighter and stop that problem? BTW, I just bought one of your single stage triggers and love it!!!

Asked by: James Knudson - 11/3/2017
A: Thank you for your recent purchase. The KIDD bolt does have tighter tolerances so it will help take some of the slop out. Good Shooting-KIDD
Was this answer helpful?  13 of 14 Customer(s) found this Answer helpful.
Answer provided by: Shay (11/5/2018)

Q: will your bolt fit my factory receiver?

Asked by: dennis diemand - 10/14/2017
A: Yes, the KIDD bolt will fit into a factory receiver. Good Shooting-KIDD
Was this answer helpful?  12 of 12 Customer(s) found this Answer helpful.
Answer provided by: Shay (10/14/2017)

Q: Do you still offer a black coating on your bolts?

Asked by: James - 7/11/2017
A: Hi James,
The black finish for KIDD bolts is now available. Good Shooting-Shalee
Was this answer helpful?  9 of 10 Customer(s) found this Answer helpful.
Answer provided by: Shay (10/4/2017)
A: We do not have black bolts at this time. We do plan on offering them in the near future. Good Shooting-Shalee
Was this answer helpful?  7 of 8 Customer(s) found this Answer helpful.
Answer provided by: Shay (7/12/2017)

Q: Will bolt work with stock ruger receiver ? Take/down model

Asked by: Ricky Bryan - 6/9/2017
A: Yes, this bolt will work in the factory receiver. Good Shooting-Shalee
Was this answer helpful?  14 of 14 Customer(s) found this Answer helpful.
Answer provided by: Shay (6/12/2017)

Q: will this bolt fit/work in a stock 10/22 receiver? (just purchased new)

Asked by: fred - 4/9/2017
A: This bolt should drop into your factory receiver. Good Shooting-Shalee
Was this answer helpful?  42 of 43 Customer(s) found this Answer helpful.
Answer provided by: Shay (4/10/2017)

Q: Will your Kidd 22LR Bolt drop into a standard Ruger 10/22? What improvements would I expect to see? Thanks

Asked by: Abel - 4/7/2017
A: This bolt should drop into a factory receiver. It has proper head spacing and firing pin protrusion to improve reliability. The "pinned" firing pin gives you consistent ignition . We radiused and polished the rear of the bolt for improved cycling and it comes with our upgraded firing pin and extractor. Good Shooting-Shalee
Was this answer helpful?  117 of 119 Customer(s) found this Answer helpful.
Answer provided by: Shay (4/10/2017)

Q: Do you sell your extractor separately? I'm planning to purchase a trigger kit and want to upgrade my extractor as well, and would hate to have to buy a Volquartsen ;) Thanks!

Asked by: Charles - 2/12/2017
A: Hi Charles,
We do sell extractors. It is part #13. Good Shooting-KIDD
Was this answer helpful?  10 of 11 Customer(s) found this Answer helpful.
Answer provided by: Shay (2/13/2017)

Q: Hello, are you guys still making the scalloped black bolts? I only see the silver ones? Thanks

Asked by: Dutn - 7/23/2016
A: We do not have black bolts at this time and we are not sure when we will have them again. Good shooting! KIDD
Was this answer helpful?  17 of 22 Customer(s) found this Answer helpful.
Answer provided by: Administrator (7/25/2016)

Q: Is there a specific lube or product you recommend for the bolt?

Asked by: Vinny - 7/4/2016
A: Hi Vinny, We sell some maintenance products that would be good for your bolt. Here is the link: http://www.coolguyguns.com/Maintenance-_c_12.html. Good shooting! KIDD
Was this answer helpful?  19 of 23 Customer(s) found this Answer helpful.
Answer provided by: Administrator (7/5/2016)

Q: Will this bolt work with a 10/22 takedown?

Asked by: Mark - 7/4/2016
A: Yes. Good shooting! KIDD
Was this answer helpful?  35 of 36 Customer(s) found this Answer helpful.
Answer provided by: Administrator (7/5/2016)

Q: Does this come with guide rod and spring kit? If not, can I use Ruger stock one?

Asked by: Gary - 4/19/2016
A: Hi Gary, Our bolt assembly comes complete with the firing pin and extractor but not with the guide rod, spring, and handle. The stock one can be used with our bolt. Good shooting! KIDD
Was this answer helpful?  57 of 59 Customer(s) found this Answer helpful.
Answer provided by: Administrator (4/20/2016)

Q: Would the matte black finish ware off after cycling?

Asked by: GBigs - 3/29/2016
A: Thank you for your interest. We have our bolts covered in a finish that was developed initially to coat racing engines. So it doesn't ware off after cycling in an action. Good shooting! KIDD
Was this answer helpful?  36 of 40 Customer(s) found this Answer helpful.
Answer provided by: Administrator (4/5/2016)

Q: I m building a .22LR using all KIDD parts except for the barrel which will be a green mountain 20" bull barrel which I already have. When mating the barrel to the KIDD receiver do I need to check the headspace with a go - no go gauge? Or will the headspace be correct because of the bolt tolerance? Thank you

Asked by: Wes - 2/15/2016
A: There is no need to "set" headspace as it is already build into our bolt. Regarding the mating of the barrel and receiver, use the shoulder of the barrel as your stopping point indicator. When the barrel shoulder is up against the receiver you should be good. Good shooting! KIDD
Was this answer helpful?  36 of 36 Customer(s) found this Answer helpful.
Answer provided by: Administrator (2/16/2016)

Q: Does it come with firing pin an extractor?

Asked by: Ryan - 2/9/2016
A: Yes, our bolt comes with our firing pin and extractor installed. Good shooting! KIDD
Was this answer helpful?  70 of 73 Customer(s) found this Answer helpful.
Answer provided by: Administrator (2/9/2016)