0
Shopping Cart
Worth 0
Home > 10-22 KIDD TRIGGERS > *Upgrades for Ruger 10/22
KIDD Weight Tuning Kit for the Ruger 10-22
Ruger 10-22 accessory trigger weight tuning kit

KIDD Weight Tuning Kit for the Ruger 10-22

Part Number 113
review 2 Review(s)
5
Write a Review Write a Review
Your Price:
7.50
Availability:
In Stock
Quantity
Email a friend Email a friend
Description
  • Ruger 10-22 springs
  • tunes your 10-22 Ruger style trigger pull

Use the trigger weight tuning springs to set/tune the pull weight in the Ruger 10-22 trigger design for an aftermarket upgrade.  This spring affects both the pull weight and reset of the trigger.  A stronger spring may be necessary if your trigger is not resetting consistently.   With the KIDD Trigger job kit installed in the Ruger polymer trigger guard the unmarked spring will set the trigger pull weight to approximately 1 3/4 lb., white 2 1/4 lb., red 2 3/4 lb., green 3 1/4 lb., blue 3 3/4 lb.  Please keep in mind that these results are approximates due to the fact that we do not manufacture the Ruger components.  Best results will be achieved with the KIDD Trigger job kit installed in a Ruger polymer guard. 

 

This spring is located in the trigger guard behind the trigger blade with a plunger capping it off.  In order to gain access to this area the hammer must be removed along with the sub-assembly of the sear/disconnect/trigger blade.  When removing the sub-assembly of the sear/disconnect/trigger blade, it is best to replace the trigger pin with the shorter slay pin used in assembling the KIDD Trigger job kit. 

 

 

KIDD Trigger job kit instructions follow:

 

Before installation of KIDD drop in trigger unit, make sure gun is unloaded and safety is on. Also, make sure the safety works and trigger is in working condition.

Disassemble:

1.       First, you must remove the trigger assembly from the receiver.

2.       Click safety on to fire. With hand over hammer, de-cock the hammer. Pull hammer forward to remove hammer strut spring assembly.

3.       Remove upper ejector and bolt hold open pin to release bolt hold open spring and ejector. Slightly push magazine latch pin enough to release bolt hold open. (Magazine latch pin may easily fall out.) After removing bolt hold open, slide pin back in to keep magazine latch secured. Push hammer pin out to remove hammer and spring.

4.       Place trigger guard upside down on a flat surface. Hold back trigger blade as you slide out trigger pin with the other hand. (Holding the trigger blade back keeps plunger spring from flying out.) Flip trigger guard back over. Trigger should only have safety, magazine latch and magazine latch plunger intact.

Installation:                  

1.       While holding plunger in place, drop trigger unit in guard with trigger blade on the bottom. Align the trigger pivot hole with the slay pin. (Slay pin is the small pin within the drop in trigger unit.) Using the smaller dowel pin provided, slide into trigger pivot hole removing slay pin. (Slay pin should also easily slide out.)

2.       To install hammer with flat side of hammer forward, place spring over bushing on right side of hammer with crooked end of spring on top and slide into guard with the groove facing down. Slide in larger dowel pin provided to secure hammer in place.

3.       Slightly slide out magazine latch pin to replace bolt hold open. Slide spring over so that the crooked end lands on top of bolt hold open. Push down straight end of spring to slide in dowel pin while also putting ejector back into place.

4.       Pull hammer forward to drop in hammer spring with the retainer end going into hole in rear end of trigger guard (slit facing up). Cock hammer into place. Put safety on. Trigger is now ready to be installed in your receiver.

 

Customer Reviews
Rating YOU NEED THIS!!
 
I wasn't quite ready to take the plunge and buy a complete trigger pack, so I purchased this trigger spring kit. I can't believe there aren't more reviews about this product. This is hands down the biggest upgrade you can do to your trigger pull. The lightest spring weight is perfect for my trigger.
  Reviewed by:   from Atlanta. on 2/15/2014
5/5
Rating Disabled
 
Ok so most people know Kidd quality! I'd like to say that they are one of the only company's that has fare shipping rates on small parts orders! This cost $3.00 to ship! I've not ordered things on other sites just because they charge more for shipping than the cost of the parts! Thanks Kidd for yet another great quality!
  Reviewed by:   from St. Louis MO. on 5/10/2013
5/5
Related Items
Ruger 10-22 Magazine Release Levers-interchangeable
Ruger 10-22 Magazine Release Levers-interchangeable
Average Rating 4 Review(s)
Your Price: 34.95
Ruger 10-22 Auto Bolt Release
Ruger 10-22 Auto Bolt Release
Average Rating 11 Review(s)
Your Price: 10.95
Ruger 10-22 "trigger job" kit
Ruger 10-22 "trigger job" kit
Average Rating 49 Review(s)
Your Price: 105.00
Browse Similar Items